Are there near terms plans to support these devices? I would love to connect mine to my new Mac Mini.
Promise Pegasus 2 R6 on the new Apple Silicon machines
- 1.7K Views
- Last Post 12 January 2022
Derek Krencik
posted this
19 November 2020
+1
Paul Kerry
posted this
17 December 2020
The is a driver out for M1 macs or apple silicon
I have tested this out on my macbook pro m1 with my pegasus 2 R4 works ok, with some bugs but it will mount your device the issue I see is speed. But I am sure this will get ironed out over time.
Sam Pullara
posted this
17 December 2020
This works for me on a Mac Mini M1 with a Pegasus2 R6 as well even though the driver claims it only works for Pegasus3.
Paul Kerry
posted this
22 December 2020
This works for me on a Mac Mini M1 with a Pegasus2 R6 as well even though the driver claims it only works for Pegasus3.
Yeah, I suspect they all use similar ways to connect in Mac OS regardless of being thunderbolt 3 or thunderbolt 2.
either that or they always put support for all Pegasus devices in all their products.
The funny thing is their chat support is actually saying it supports more than just the pegasus 3 units. So maybe there is a communication error internally? hard to say all I know is it just works, with pretty much all pegasus units 1, 2 , 3
Thomas Agatz
posted this
23 December 2020
I've had my old Pegasus R6 series 1 perfectly connected to my new MBP M1 for the last week, by following the guide.
- Liked by
-
Igor Schlumberger
posted this
27 February 2021
- Last edited 27 February 2021
Dear All,
Thank you for the documentation, the new driver and the explanations.
I did all well, installing the new Driver on my MacBook Air M1 with BigSur 11.2.2
In System Report I now see the Promise R4:
Pegasus R-Series:
Vendor Name: Promise Technology, Inc.
Device Name: Pegasus R-Series
Mode: Thunderbolt
Device ID: 0x1
Vendor ID: 0x2
Device Revision: 0x1
UID: 0x0002000000080F40
Route String: 1
Firmware Version: 22.3
Device Micro Firmware Version: 1.0.0
Port (Upstream):
Status: Device connected
Link Status: 0x2
Speed: Up to 10Gb/s x2
Port Micro Firmware Version: 1.4.14
Cable Firmware Version: 1.0.16
Cable Serial Number: C4M4165051XF798A1
Port:
Status: No device connected
Link Status: 0x7
Speed: Up to 10Gb/s x2
Port Micro Firmware Version: 1.4.14
I'm connected with the Apple USB-C Thunderbolt Adaptator and a Apple Thunderbolt Câble to the Promise.
I rebooted the mac.
If a une an older MacBook Pro with the same cable (without the adatptator), the Drive will mount. On my MacBook Air 16 Go, the Drive did not mount.
When I launch Pegasus Utility, the Drive doesn't show.
Any Idea on something to test or to do?
I have 2 Pegasus R4 and one R6.
Best,
Igor
Sam Edwards
posted this
12 January 2022
Just tried to install the new driver above on a MBP16 M1 Max. Followed the instructions to the letter, and the mac locks up whenever a Pegasus2 or Pegasus1 is attached. Very dissappointing.
Sam
Edward K
posted this
12 January 2022
I'm also having a TERRIBLE time with the Pegaus.
My Pegasus2 (R8) keeps giving "Disk Not Ejected Properly" messages whenever the machine sleeps
(so about 20 messages in 2 hours)
